ppm-series ? ppm05-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 ppm 05-e-xxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications input voltage range 85 ? 264 vac or 110 ? 370 vdc universal input frequency 47 ? 440 hz input (inrush) current 110 vac 230 vac ppm05 models 110 ma (10a), typ. 70ma (20a), typ. external input fuse (recommended) 1a / 250v slow blow output specifications voltage accuracy 2%, typ (3% at 3.3 vout) input variation 0.5%, typ load variation (10-100%) 1% , typ ripple and noise (20mhz bandwidth) 30mv pk-pk, typ short circuit protection continuous, auto resume over output voltage protection diode clamp common specifications temperature range -25c to +70 c power derating 2% / c case temperature +95c (max) storage -40c to +105 c hold up time 50ms, typ. (230vac) humidity (non condensing) 95%, max. temperature coefficient 0.02%/c switching frequency 100khz, typ i/o isolation voltage 4000vac / 1min. leakage current none emi / rfi conducted en55011, level a emc compliance esd iec/en 61000-4-2 15kv/15kv rf iec/en 61000-4-3 10v/m eft / bursts iec/en 61000-4-4 4kv surge iec/en 61000-4-5 2kv/4kv safety standards iec60601, en60601 safety class class 2 case material ul94v-0 rated reliability calculated mtbf (mil-hdbk-217f) > 300,000 hrs weight ~ 35g mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the ppm - series are high efficiency green power moduls with various packaging provided by peak. the features of this se ries are: wide input voltage, dc and ac all in one, high efficiency, hig h reliability, low loss, safety isolation etc. they are widely used in indus trial, office and civil equipments.. ppm-series 5 watt univ. 85-264vac (110-370vdc) single output over voltage protection (out) 4 kv ac i/o isolation low ripple and noise high efficiency rev.04-2012
ppm-series ? ppm05-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # p o w e r ( w ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) single output ppm05-e-3r3elf 4.2 3.3 1250 66 ppm05-e-05elf 5 5 1000 72 ppm05-e-09elf 5 9 550 74 ppm05-e-12elf 5 12 420 76 PPM05-E-15ELF 5 15 333 76 ppm05-e-24elf 5.5 24 230 78 if you need other specifications, please enquire. package / pinning / derating all dimensions are typical in millimeters (inches). pin diameter: 0.5 +/0.05 (0.02 +/0.002) pin pitch tolerance: +/0.35 (+/0.014) case tolerance +/0.5 (+/0.02) specification may change without notice. modelcode datecode 15.16 (0.60) 2" x 1" C plastic case 2 4 1 3 45.72 (1.80) 6.00 (0.24) pe a k 50.80 (2.00) bottom view # single 1 ac (n) 2 ac (l) 3 + vout 4 - vout pin connections
ppm-series ? ppm05-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 app notes: measure typical applications ppm-series external typical value model c1 c2 ppm05-e-3r3elf 47 0.1 ppm05-e-05elf 47 0.1 ppm05-e-09elf 33 0.1 ppm05-e-12elf 33 0.1 PPM05-E-15ELF 33 0.1 ppm05-e-24elf 10 0.1 note 1. output filtering capacitors c1 and c3 are electr olytic capacitors, it is recommended to use high frequency and low impedance electrolytic capac itors. for capacitance and current of capacitor please refer to manufacture?s datasheet. voltage derating of capacitor should be 80% or above. c2 is ceramic capacitor, it is used t o filter high frequency noise. tvs is a recommended component to protect post-circuits (if converter fails). 2. to protect the device from damage, external circ uit is required to models at inrush and electrical fast transients experiment, mov is requi red to ppm05 models, model: 471kd14; it is recommended to connect fuse, the parameter for p pm05 models is 1a/250v slow blow. external input ntc is recommended to use 5d-14 or 1 0 /2w wire-round resistor. 3. if emc performance is required, recommended to a dd ?emc filter? at the input end c6:x capacitor, recommended parameter 0.1uf/275v; c7,c8:y capacitor, recommended parameter 2200pf/400 v; nf: common model choke, recommended inductance is a bout 10mh-30mh.
|
